The following default configurations apply to SRX240 factory default settings
                                                                                     

Default configuration for Security Zone, Security Policy and NAT Rule:

2. Cluster Network Diagram in this LAB

If your devices were used before, it is best to reset them into default configuration. Here are some four different ways and commands to do it

a. request services fips zeroize
b. request system zeroize
c. Delete all commands in the configuration mode
root@# delete    
This will delete the entire configuration
Delete everything under this level? [yes,no] (no) no

you will need to set root password to be able to commit the changes
d. load factory-default

3.  Set root password

By default, there is no password for root user.

set system root-authentication plain-text-password

4. Delete some default configurations on Node0

Please keep this in mind, you will need to delete those configuration on both nodes, node0 and node1. 

delete system name-server
delete system services dhcp

delete vlans

delete interfaces vlan

delete interfaces ge-0/0/0 unit 0

delete interfaces ge-0/0/1 unit 0
delete interfaces ge-0/0/2 unit 0
delete interfaces ge-0/0/3 unit 0
delete interfaces ge-0/0/4 unit 0
delete interfaces ge-0/0/5 unit 0
delete interfaces ge-0/0/6 unit 0
delete interfaces ge-0/0/7 unit 0
delete interfaces ge-0/0/8 unit 0
delete interfaces ge-0/0/9 unit 0
delete interfaces ge-0/0/10 unit 0
delete interfaces ge-0/0/11 unit 0
delete interfaces ge-0/0/12 unit 0
delete interfaces ge-0/0/13 unit 0
delete interfaces ge-0/0/14 unit 0
delete interfaces ge-0/0/15 unit 0
delete security

commit

5. Enable Cluster on node 0 and reboot

root>set chassis cluster cluster-id 2 node 0 reboot 

6. Basic configuration based on the topology

set groups node0 system host-name fw-a
set groups node0 interfaces fxp0 unit 0 family inet address 10.9.12.9/24
set groups node0 interfaces fxp0 unit 0 family inet address 10.9.12.8/24 master-only
set groups node1 system host-name fw-b
set groups node1 interfaces fxp0 unit 0 family inet address 10.9.12.10/24
set groups node0 interfaces fxp0 unit 0 family inet address 10.9.12.8/24 master-only
set apply-groups “${node}”
set chassis cluster reth-count 2
set chassis cluster redundancy-group 0 node 0 priority 200
set chassis cluster redundancy-group 0 node 1 priority 100
set chassis cluster redundancy-group 1 node 0 priority 200
set chassis cluster redundancy-group 1 node 1 priority 100
set interfaces fab0 fabric-options member-interfaces ge-0/0/2
set interfaces fab1 fabric-options member-interfaces ge-5/0/2
set interfaces ge-0/0/3 gigether-options redundant-parent reth0
set interfaces ge-5/0/3 gigether-options redundant-parent reth0
set interfaces ge-0/0/4 gigether-options redundant-parent reth1
set interfaces ge-5/0/4 gigether-options redundant-parent reth1
set interfaces reth0 redundant-ether-options redundancy-group 1
set interfaces reth1 redundant-ether-options redundancy-group 1
set security zones security-zone Zone1
set security zones security-zone Zone2
set security zones security-zone Zone1 host-inbound-traffic system-services all
set security zones security-zone Zone2 host-inbound-traffic system-services all
set interfaces reth0 unit 0 family inet address 10.9.132.18/24
set security zones security-zone Zone1 interfaces reth0.0
set interfaces reth1 unit 0 family inet address 10.9.136.18/24
set security zones security-zone Zone2 interfaces reth1.0


set system backup-router destination 10.0.0.0/8 10.9.12.1
set routing-options static route 0.0.0.0/0 next-hop 10.9.12.1

set security policies from-zone Zone1 to-zone Zone2 policy allow_any match source-address any
set security policies from-zone Zone1 to-zone Zone2 policy allow_any match destination-address any
set security policies from-zone Zone1 to-zone Zone2 policy allow_any match application any
set security policies from-zone Zone1 to-zone Zone2 policy allow_any then permit
set security policies from-zone Zone2 to-zone Zone1 policy allow_any match source-address any
set security policies from-zone Zone2 to-zone Zone1 policy allow_any match destination-address any
set security policies from-zone Zone2 to-zone Zone1 policy allow_any match application any
set security policies from-zone Zone2 to-zone Zone1 policy allow_any then permit

7. Enable Cluster on node 1 and reboot

After did cable connections between two clusters on g0/1 and g0/2, we can enable cluster node 1

Before enable cluster on node1, some basic configuration has to be deleted.

delete system name-server
delete system services dhcp

delete vlans
delete interfaces vlan

delete interfaces ge-0/0/0 unit 0
delete interfaces ge-0/0/1 unit 0
delete interfaces ge-0/0/2 unit 0
delete interfaces ge-0/0/3 unit 0
delete interfaces ge-0/0/4 unit 0
delete interfaces ge-0/0/5 unit 0
delete interfaces ge-0/0/6 unit 0
delete interfaces ge-0/0/7 unit 0
delete interfaces ge-0/0/8 unit 0
delete interfaces ge-0/0/9 unit 0
delete interfaces ge-0/0/10 unit 0
delete interfaces ge-0/0/11 unit 0
delete interfaces ge-0/0/12 unit 0
delete interfaces ge-0/0/13 unit 0
delete interfaces ge-0/0/14 unit 0
delete interfaces ge-0/0/15 unit 0
delete security

commit

After commit, enable chassic cluster :

set chassis cluster cluster-id 1 node 1 reboot 

note: If you are using multiple Juniper Cluster in same Ethernet Environment, they have to configure unique cluster-id. Else the mac address will be conflicted on switch interface and firewall will not be able to handle network traffic properly in that zone. In following example, cluster-id is set to 5 to avoid conflicting. The range for the cluster-id is 0-15.

user@host> set chassis cluster cluster-id 5 node 0 reboot
Successfully enabled chassis cluster. Going to reboot now.

{primary:node0}[edit]
user@host> show chassis cluster status
Cluster ID: 5
Node                  Priority          Status    Preempt  Manual failover

Redundancy group: 0 , Failover count: 1
    node0                   100         primary        no       no
    node1                   1           secondary      no       no

Redundancy group: 1 , Failover count: 1
    node0                   0           primary        no       no
    node1                   0           secondary      no       no

Verification:

You can check the cluster status with the following commands.

show chassis cluster status
show chassis cluster interfaces
show chassis cluster statistics
show chassis cluster control-plane statistics
show chassis cluster data-plane statistics
show chassis cluster status redundancy-group 1

Reference:

By Jon

Leave a Reply

Ads Blocker Image Powered by Code Help Pro

Ads Blocker Detected!!!

We have detected that you are using extensions to block ads. Please support us by disabling these ads blocker.

%d